| Included | |
|---|---|
| Type / Base | Epoxy-mod acrylic latex |
| Best Use | Patios, basements, light garages |
| Coverage | 500–600 ft²/gal |
| Dry Time (Touch) | ~1 hr |
| Recoat Time | 4 hrs |
| Traffic Ready | Foot: next day, Full: 30 days |
| Hot Tire Resistance | Moderate |
| Slip Resistance | Low gloss |
| Sheen | Low Sheen / Gloss |
| VOC Content | ~45 g/L |
| Primer Needed | Optional (bare or stained) |
| Surface Prep | Clean, dry, etched |
| Application | Brush, roller |
| Cleanup | Soap & water |
| Certifications | Green Seal aligned, SCAQMD |
| Included | |
|---|---|
| Type / Base | Acrylic urethane (waterborne) |
| Best Use | Floors, walls, commercial use |
| Coverage | 350–450 ft²/gal |
| Dry Time (Touch) | 15 min (vertical), 1 hr floor |
| Recoat Time | 1 hr |
| Traffic Ready | Foot: 24 hrs |
| Hot Tire Resistance | Moderate |
| Slip Resistance | Moderate (additive optional) |
| Sheen | Satin or Gloss |
| VOC Content | ~50–100 g/L |
| Primer Needed | Optional |
| Surface Prep | Degrease, dull glossy areas |
| Application | Brush, roller, spray |
| Cleanup | Soap & water |
| Certifications | MPI #115, #138, #157, LEED v4 |
| Included | |
|---|---|
| Type / Base | Acrylic latex + texture |
| Best Use | Walkways, stairs, decks |
| Coverage | 80–120 ft²/gal |
| Dry Time (Touch) | ~1–2 hrs |
| Recoat Time | 8 hrs |
| Traffic Ready | Foot: 24 hrs, Full: 4–5 days |
| Hot Tire Resistance | Not applicable |
| Slip Resistance | Very High (built-in texture) |
| Sheen | Flat |
| VOC Content | ~130 g/L |
| Primer Needed | Yes on wood or metal |
| Surface Prep | Remove loose paint, clean |
| Application | Brush, roller |
| Cleanup | Soap & water |
| Certifications | ADA Slip Rating >1.0 |
| Included | |
|---|---|
| Type / Base | Epoxy‑modified acrylic |
| Best Use | Garages, basements, concrete, masonry, stucco, cinder block, brick; interior and exterior |
| Coverage | 350–450 ft²/gal |
| Dry Time (Touch) | 1–2 hours |
| Recoat Time | 4 hours |
| Traffic Ready | Light foot traffic: 8 hours; vehicle traffic: 3–5 days |
| Hot Tire Resistance | Resists hot tire pick-up |
| Slip Resistance | (Not specifically stated; typical satin finish—somewhat low gloss) |
| Sheen | Satin, with gloss reading 15–30 @ 60° |
| VOC Content | < 50 g/L |
| Primer Needed | Self-priming (primer optional); on bare concrete, thin first coat with 1 pt water/gal |
| Surface Prep | Must be clean, dry, etched or abraded; new concrete – cure 30 days; remove grease, loose paint, etch or grind |
| Application | Stir before use; apply two coats by brush or roller, second coat cross-direction |
| Cleanup | Water (soap & water) |
| Certifications | Compliant with OTC, OTC II, CARB, CARB07, CARB19, UTAH, AZMC, SCAQMD; Green Seal alignment mentioned elsewhere |
| Included | |
|---|---|
| Type / Base | 2-Part waterborne epoxy |
| Best Use | Garages, basements |
| Coverage | 250–300 ft²/kit |
| Dry Time (Touch) | ~2 hrs |
| Recoat Time | 8 hrs |
| Traffic Ready | Foot: 24 hrs, Car: 72 hrs |
| Hot Tire Resistance | High |
| Slip Resistance | Smooth, semi-gloss |
| Sheen | Semi-Gloss |
| VOC Content | <250 g/L |
| Primer Needed | No primer needed |
| Surface Prep | Etch, degrease |
| Application | Roller, brush |
| Cleanup | Soap & water |
| Certifications | USDA Acceptable, LEED, SCAQMD |
| Included | |
|---|---|
| Type / Base | Acrylic emulsion |
| Best Use | Residential pools |
| Coverage | 300–350 ft²/gal |
| Dry Time (Touch) | ~1 hr |
| Recoat Time | 4 hrs |
| Traffic Ready | Fill after: 3 days |
| Hot Tire Resistance | N/A |
| Slip Resistance | Moderate |
| Sheen | Satin |
| VOC Content | <100 g/L |
| Primer Needed | No primer needed |
| Surface Prep | Clean, etched, pH neutral |
| Application | Brush, roller |
| Cleanup | Soap & water |
| Certifications | VOC compliant |
| Included | |
|---|---|
| Type / Base | Chlorinated rubber-based coating |
| Best Use | Concrete & plaster pools, fountains |
| Coverage | 250–300 ft²/gal |
| Dry Time (Touch) | 4–6 hrs |
| Recoat Time | 24 hrs |
| Traffic Ready | Immersion: 5–7 days after final coat |
| Hot Tire Resistance | Not applicable |
| Slip Resistance | Moderate |
| Sheen | Stain |
| VOC Content | ~340 g/L |
| Primer Needed | Clean, bare surfaces only |
| Surface Prep | Clean, dry, and free from contaminants |
| Application | Brush, roller, or airless spray |
| Cleanup | Solvent (xylene or recommended thinner) |
| Certifications | Meets federal VOC limits for pool coatings |
| Included | |
|---|---|
| Type / Base | 2-Part epoxy |
| Best Use | Commercial or new concrete pools |
| Coverage | 225–275 ft²/kit |
| Dry Time (Touch) | 6–8 hrs |
| Recoat Time | 24 hrs |
| Traffic Ready | Fill after: 7–10 days |
| Hot Tire Resistance | N/A |
| Slip Resistance | Moderate |
| Sheen | Gloss |
| VOC Content | ~150 g/L |
| Primer Needed | Primer recommended |
| Surface Prep | Sandblast or acid wash |
| Application | Brush, roller |
| Cleanup | Xylene or solvent |
| Certifications | Epoxy pool performance specs |
 |  |  |  |  |  |  |  | |
|---|---|---|---|---|---|---|---|---|
| Product | BM Floor & Patio | HP3900-Command | INSL-X Sure Step (Tintable) | GarageGuard® 1-Part (Titable) | GarageGuard® 2-Part Kit (Titable) | INSL-X Water-Based Pool Paint | Rubber Based Pool Paint – Satin | INSL-X Epoxy Pool Paint |
| Price | Buy Now From $36.99 | Buy Now From $104.99 | Buy Now From $78.99 | Buy Now From $78.99 | Buy Now From $105.99 | Buy Now From $104.99 | Buy Now From $112.59 | Buy Now From $239.99 |
| Type / Base | Epoxy-mod acrylic latex | Acrylic urethane (waterborne) | Acrylic latex + texture | Epoxy‑modified acrylic | 2-Part waterborne epoxy | Acrylic emulsion | Chlorinated rubber-based coating | 2-Part epoxy |
| Best Use | Patios, basements, light garages | Floors, walls, commercial use | Walkways, stairs, decks | Garages, basements, concrete, masonry, stucco, cinder block, brick; interior and exterior | Garages, basements | Residential pools | Concrete & plaster pools, fountains | Commercial or new concrete pools |
| Coverage | 500–600 ft²/gal | 350–450 ft²/gal | 80–120 ft²/gal | 350–450 ft²/gal | 250–300 ft²/kit | 300–350 ft²/gal | 250–300 ft²/gal | 225–275 ft²/kit |
| Dry Time (Touch) | ~1 hr | 15 min (vertical), 1 hr floor | ~1–2 hrs | 1–2 hours | ~2 hrs | ~1 hr | 4–6 hrs | 6–8 hrs |
| Recoat Time | 4 hrs | 1 hr | 8 hrs | 4 hours | 8 hrs | 4 hrs | 24 hrs | 24 hrs |
| Traffic Ready | Foot: next day, Full: 30 days | Foot: 24 hrs | Foot: 24 hrs, Full: 4–5 days | Light foot traffic: 8 hours; vehicle traffic: 3–5 days | Foot: 24 hrs, Car: 72 hrs | Fill after: 3 days | Immersion: 5–7 days after final coat | Fill after: 7–10 days |
| Hot Tire Resistance | Moderate | Moderate | Not applicable | Resists hot tire pick-up | High | N/A | Not applicable | N/A |
| Slip Resistance | Low gloss | Moderate (additive optional) | Very High (built-in texture) | (Not specifically stated; typical satin finish—somewhat low gloss) | Smooth, semi-gloss | Moderate | Moderate | Moderate |
| Sheen | Low Sheen / Gloss | Satin or Gloss | Flat | Satin, with gloss reading 15–30 @ 60° | Semi-Gloss | Satin | Stain | Gloss |
| VOC Content | ~45 g/L | ~50–100 g/L | ~130 g/L | < 50 g/L | <250 g/L | <100 g/L | ~340 g/L | ~150 g/L |
| Primer Needed | Optional (bare or stained) | Optional | Yes on wood or metal | Self-priming (primer optional); on bare concrete, thin first coat with 1 pt water/gal | No primer needed | No primer needed | Clean, bare surfaces only | Primer recommended |
| Surface Prep | Clean, dry, etched | Degrease, dull glossy areas | Remove loose paint, clean | Must be clean, dry, etched or abraded; new concrete – cure 30 days; remove grease, loose paint, etch or grind | Etch, degrease | Clean, etched, pH neutral | Clean, dry, and free from contaminants | Sandblast or acid wash |
| Application | Brush, roller | Brush, roller, spray | Brush, roller | Stir before use; apply two coats by brush or roller, second coat cross-direction | Roller, brush | Brush, roller | Brush, roller, or airless spray | Brush, roller |
| Cleanup | Soap & water | Soap & water | Soap & water | Water (soap & water) | Soap & water | Soap & water | Solvent (xylene or recommended thinner) | Xylene or solvent |
| Certifications | Green Seal aligned, SCAQMD | MPI #115, #138, #157, LEED v4 | ADA Slip Rating >1.0 | Compliant with OTC, OTC II, CARB, CARB07, CARB19, UTAH, AZMC, SCAQMD; Green Seal alignment mentioned elsewhere | USDA Acceptable, LEED, SCAQMD | VOC compliant | Meets federal VOC limits for pool coatings | Epoxy pool performance specs |